C&P, with its ISO 17020 accreditation, specific to pressure equipment, boilers and piping complies with the requirement of Workplace Safety and Health Act (WSH) and is able to provide the certification required for the export of these products destined for Singapore

Pressure equipment to be installed in the territory of Singapore must be provided with the following documents to be forwarded to the Authorised Examiner:

  • Construction drawing of the pressure vessel, including welding details.
  • Design calculations (approved by Inspection Bodies – IB) carried out according to ASME or BSI codes.
  • Layout of boiler room or room in accordance with SS 567:2011.
  • Steam piping diagrams (drawn according to ASME 31.1/31.3).
  • (For fuel or gas or steam boilers with double combustion) Letter of approval from the National Environment Agency for the installation of a chimney and purge pit.
  • (For double-fired gas or steam boilers) Gas ramp layout plan in accordance with BS EN 676 or equivalent.
  • (For tanks manufactured abroad) A manufacturing inspection report by an Accredited Inspection Body (IB) certifying that the pressure vessel has been manufactured and tested according to the accepted code or standards for pressure vessels.

If you use other pressure vessel codes, you must obtain approval from the Authorised Examiner.

You must request a copy of the IB’s accreditation certificate to verify:

  • Scope of accreditation, e.g. design verification, fabrication, inspection of pressure vessels.
  • That the certificate had not expired at the time of manufacture of the pressure vessel.

What is an Accredited Inspection Body (IB) according to the MOM?

An accredited IB refers to Conformity Assessment Bodies (CABs) accredited according to “ISO/IEC 17020 – General requirements for the operation of various types of bodies performing inspections”.

Inspection Bodies (IBs) are accredited by the Singapore Accreditation Council (SAC) or SAC’s Mutual Recognition Arrangement (MRA) partners, for design verification and inspection of new construction/fabrication of pressure vessels.

To obtain the Fabrication Survey Report, it is necessary to submit a request for quotation/intervention form AM042N, in which it is specified that the inspection is required in accordance with the construction standards according to the ASME or British Standard Codes, submit the construction drawings, the stability calculations, the welding book consisting of welding procedures and related qualifications.

Drawings shall be fully identified and shall include basic design conditions, essential dimensions, specifications of component materials, welding details, location and purpose of connections and openings, supports, required non-destructive testing, post-weld heat treatment (PWHT), test position and test pressure, corrosion tolerance and other details deemed essential for proper verification, e.g. site conditions (seismic, wind, snow, flood and the like), lifting systems and requirements for transport and installation. Any other data required for the verification of the design. You must also produce a detailed control plan with the specified inspection points.

Other Ispections

Material inspections and certification according to en 10204 type 3.2

C&P provides inspection and certification services of metallic materials to forges, foundries, rolling mills

Voluntary inspections under accreditation

C&P is an ISO 17020 type A accredited inspection body for the inspection of pressure equipment, steam generators and piping on a voluntary basis.

Australia Inspections

C&P is an ISO 17020:2012 accredited Inspection Body that includes the Australian manufacturing code AS 1210 and is therefore authorized to conduct inspections for the Australian market.

New Zeland Inspections

C&P is able to provide you with the necessary support for the export of your pressure equipment to New Zealand.

Accredited third party inspections

Inspection of pressure equipment under accreditation refers to a process of verification and evaluation of pressure equipment by accredited bodies.

DOSH Malaysia Inspections

C&P, as a DOSH approved Inspection Body, provides inspection service for exporting your products to Malaysia.

ASME Nuclear Inspections

C&P provides a team of Authorized Inspectors to ensure the highest quality, safety and compliance of pressure equipment in a nuclear power plant.

ASME Inspections

C&P as an Authorized Inspection Agency in addition to the inspection service provides its customers with support in the application and interpretation of the Code.